Minggu, 08 November 2009
Solution When The Phone Does Get Wet
Have your phone suddenly fell into the water? Then suddenly the phone can not be used anymore, or death total? How is the solution?
If you have things like that do not panic, the mind can be stressful. In this article, we will provide a way of handling a wet cell phone.
If your phone is new with warranty, forget about the warranty. Service Center for phone vendors obviously will refuse warranty if the phone has proven to be exposed to fluids, although the warranty seal still intact. A consumer has rejected the warranty claim for a damaged cell phone, on the grounds wet. And cell phone was never exposed to further research airSetelah cell phone was damaged because it is often exposed to cold ocean, which can also cause corrosion on the phone.
Drain Phone
First steps to do if the phone is under water, try to quickly pull up and immediately the phone battery. Immediately dry the outside of the phone with a clean rag or tissue, so that water does not enter more and more into the phone. If you do not intend to open the inside of the phone, you can use a hair dryer to dry it.
Once outside the dry section, casing and PCB inside the phone must be opened to drain the water remains trapped inside. If not immediately dried, then the components in it will experience corrosion and phone can not be repaired anymore. Especially if exposed to sea water, the components will experience faster corrosion.
To open the lock bolts are usually required phone casing eyed T6 screwdriver. In a candy bar phone models are usually easy to open, while the clamshell models performed better suit.
Once the phone is open, clean the remaining water with cleaning fluid such as paint thinner, IPA, or alcohol. To dissolve the dirt and residue attached to the components in the PCB, can use a toothbrush or with the help of PCB cleaning (ultrasonic Cleaner).
Power Supply
Once dry, plug it in again and try to turn on the phone using a battery or by using the Power Supply. By using the Power Supply, which shorted out components exposed to water can be easily detected. If not, then watch the movement of currents in the Power Supply. If no reaction, the possibility of problems at the circuit power supply regulator IC on the phone or on the switch on / off the phone.
If there is a reaction to the Power Supply current, the next step to do data repair software on the phone. Fashing trick is to use the software and the appropriate data cable. If the flashing process is successful, usually the phone will light up again. When the flashing process fails, there is the possibility of damage to the phone's processor and memory that needs to be checked further hardware or replacement of these components.
If you have things like that do not panic, the mind can be stressful. In this article, we will provide a way of handling a wet cell phone.
If your phone is new with warranty, forget about the warranty. Service Center for phone vendors obviously will refuse warranty if the phone has proven to be exposed to fluids, although the warranty seal still intact. A consumer has rejected the warranty claim for a damaged cell phone, on the grounds wet. And cell phone was never exposed to further research airSetelah cell phone was damaged because it is often exposed to cold ocean, which can also cause corrosion on the phone.
Drain Phone
First steps to do if the phone is under water, try to quickly pull up and immediately the phone battery. Immediately dry the outside of the phone with a clean rag or tissue, so that water does not enter more and more into the phone. If you do not intend to open the inside of the phone, you can use a hair dryer to dry it.
Once outside the dry section, casing and PCB inside the phone must be opened to drain the water remains trapped inside. If not immediately dried, then the components in it will experience corrosion and phone can not be repaired anymore. Especially if exposed to sea water, the components will experience faster corrosion.
To open the lock bolts are usually required phone casing eyed T6 screwdriver. In a candy bar phone models are usually easy to open, while the clamshell models performed better suit.
Once the phone is open, clean the remaining water with cleaning fluid such as paint thinner, IPA, or alcohol. To dissolve the dirt and residue attached to the components in the PCB, can use a toothbrush or with the help of PCB cleaning (ultrasonic Cleaner).
Power Supply
Once dry, plug it in again and try to turn on the phone using a battery or by using the Power Supply. By using the Power Supply, which shorted out components exposed to water can be easily detected. If not, then watch the movement of currents in the Power Supply. If no reaction, the possibility of problems at the circuit power supply regulator IC on the phone or on the switch on / off the phone.
If there is a reaction to the Power Supply current, the next step to do data repair software on the phone. Fashing trick is to use the software and the appropriate data cable. If the flashing process is successful, usually the phone will light up again. When the flashing process fails, there is the possibility of damage to the phone's processor and memory that needs to be checked further hardware or replacement of these components.
Langganan:
Posting Komentar (Atom)
0 komentar:
Posting Komentar